Introduction

This Article describes the Settings to establish the Connection between custo diagnostic and Cosmed Omnia.

Requirements

Minimum Version are:

custo diagnostic: 4.5.x
cosmed Omnia: 1.4

Functionality

Die aktuelle Implementierung der Schnittstelle sieht vor:

1. Patienten resp. Auftragsauswahl erfolgt in custo diagnostic

2. custo diagostic steuert kein Gerät 

3. nach Erscheinen des EKG's in custo diagnostic wird alles weitere in Omnia gemacht. Dazu erscheint nach 6 Sek. (einstellbar) dort der Dialog zur Konfiguration der Messung (Make, Profil, usw.)

4. Die laufenden Messung kann sowohl in custo diagnostic als auch in Omnia beendet werden.5 Sekunden (einstellbar) nach dem in Omnia die Messung beendet worden ist, wird trickreich versucht die Kennung der neuen Messung/Auswertung zu ermitteln

5. Die Darstellung einenr gemeinsamen Messung kann nur in custo diagnostic gemacht werden. Da bei Omnia die gleiche Auswertung aufgerufen wird, wird sonst nichts bzgl. der Kommunikation zwischen den beiden Produkten gemacht.

Settings in custo diagnostic

For the perfect operation you have to set up the following options:

1. Select Cosmed Omnia as CPET Software in the Interface Selection
   Please compare also with the "Types of the Interface"
   
   
   

2. Enable necessary Dialogues to ask the Customer for required Data
   For the Operation of Cosmed Omnia the Weight and Height of the Patient is mandatory!Enable
   
   
   

3. Enable PDF-Grabbing
   The PDF Grabbing import the PDF into the Evaluation which is printed from Cosmed Omnia as Report while the Test.
   
   
   

4. Configure the PDF Printout and the Standard Printout
   
    

5. Configure the LoginUserName and LoginPassword from Cosmed Omnia
   The Login Credentials are mandatory because its a part of the TCP/IP Communication.
   
   
   

6. Configure the Program Name of Cosmed Omnia
   This Program will be started if you launch a CPET Test in custo diagnostic.
   
   
   

Settings in Cosmed Omnia

1. Install Cosmed Omnia (min. Version 1.4) on the PC
   
   
2. Start Cosmed Omnia the first Time and make it running
   
   

3. Activate the TCP/IP Interface in the File "\%PUBLIC%\Documents\Cosmed\CosmedLab\ACS.XML". The File exists only you had start Cosmed Omnia one times. After that you have to edit the File manually.

   <ExtendedConfiguration Version="1">
     <General>
       <TimeOutMinCheckValue Type="System.Int32" Value="15" />
       <MenuMatrix Type="Tuple" TypeID="System.Int32" ID="2" TypeValue="System.Int32" Value="3" />
     </General>
     <EntityFramework>
       <SessionTimeout Type="System.Int32" Value="60" />
       <MaxRetryCount Type="System.Int32" Value="5" />
       <MaxDelay Type="System.Int32" Value="26" />
     </EntityFramework>
     <Bridge>
       <Debugger Type="System.Boolean" Value="True" />
       <Control Type="Tuple" TypeID="System.String" ID="tcp" TypeValue="System.String" Value="xml" TypeItem2="System.String" Item2="utf-8" TypeItem3="System.String" Item3="5530" TypeItem4="System.String" Item4="OmniaXB" />
       <Legacy Type="Tuple" TypeID="System.String" ID="legacy" TypeValue="System.String" Value="raw" TypeItem2="System.String" Item2="ascii" TypeItem3="System.String" Item3="" TypeItem4="System.String" Item4="" />
     </Bridge>
     <Ergo>
       <ShowDataOnProtocolChart Type="System.Boolean" Value="True" />
     </Ergo>
   </ExtendedConfiguration>

    To activate the Communication via TCP/IP you have to insert this Line inside the Section <Bridge>:

       <Control Type="Tuple" TypeID="System.String" ID="tcp" TypeValue="System.String" Value="xml" TypeItem2="System.String" Item2="utf-8" TypeItem3="System.String" Item3="5530" TypeItem4="System.String" Item4="OmniaXB" />
   

   Please be careful that only one Line of the Type <Control> in the Section <Bridge> exists.

    

4. Start Cosmed Omnia
   Login as an Administrator. You can use these Credential also in the Configuration in custo diagnostic.
   With the Patient "DEMO SUBJECT" every time a Test can be performed.
   
   
5. Configure the Device K5
   
   
   
6. Start a test once time and select 'PC Software ECG' as HR Source and 'Ergoline900' as the bike. This is only possible after you had selected the Device K5!

   
   
   

Types of the Interface

In custo diagnostic → Settiungs → System → Workstation

the Type of Interface to Cosmed Omnia can be selected. This is comparable to an Operation Mode. The Selection is described as View from custo diagnostic.

Spezielle Einstellungen in custo diagnostic

Die (speziellen) Einstellungen für die Anbindung an Omnia ist unter im Einstellungseditor unter CSC->Daten-Export\CosmedOmnia zu finden. Folgende Einstellungen existieren: